亚洲欧美国产精品专区久久,一卡一卡三卡四卡不卡乱码在线观看,无码国产伦一区二区三区视频,疯狂 喷水爽www噜噜噜,国产精品日老太婆

電梯門套施工方案
The elevator door construction scheme
1、將廳門處門洞進行處理。廳門處一般是安裝石材覆蓋在表面。石材在安裝前要進行表面處理，保持清潔和干燥度，含水率要小于8%。
1, the hall door at the door handle. Hall door is generally installed stone covered in the surface. The stone shall be treated with surface treatment before installation. It shall be clean and dry, with a moisture content of less than 8%.
2、用安裝門套的石材應該保持花紋、顏色的一致性。所以要進行仔細甄選，避免出現嚴重的色差和花紋差異性。每一層的所有電梯門套石材都要保持統一性。

2, with the installation of door should maintain consistency of stone pattern, color. Therefore, careful selection should be carried out to avoid severe color difference and pattern difference. All the elevator door stone of each layer to maintain unity.
3、正式安裝石材之間，再將石材做一次徹底清理，結構部分不能留有渣質，表面無積灰污垢。然后用墨線彈出水平線和垂直線。
3, the formal installation of stone between, and then make a thorough cleaning of stone, the structural part of the slag can not be retained, the surface without ash fouling. Then use the pop-up Moxian horizontal and vertical lines.
4、根據彈出的線條位置，使用鉆機在需要打孔處打孔。孔眼的直徑一般是8mm左右，深度是12mm左右。按照施工標準，每塊石板上、下面都要打孔眼，位于石板中間位置。
4, according to the pop-up line position, use drilling machine in need punch hole drill. The diameter of the hole is about 8mm, and the depth is about 12mm. According to the construction standard, every stone slab should be lined with holes, located in the middle of the stone slab.
5、將膨脹螺栓固定在墻面上，然后將角架固定好，再將掛件安裝在角架上。
5. Fix the expansion bolt on the wall surface, then fix the angle frame, and then install the pendant on the corner frame.
6、角架和掛件安裝好之后，進行石材開槽工序。將石材固定在掛件上時使用專用的大理石膠，黏結好之后反復壓幾次，確定不會脫落。
6, after the angle and the pendant installation, carries on the stone slotting process. When the stone is fixed on the pendant, use the special marble glue, and then press it several times to make sure it won't fall off.
7、安裝好之后的電梯門套應該做到光面平整，立面垂直，接縫平直，接縫寬度的偏差不能超過2mm。
The elevator door 7, installed should be smooth flat, vertical, straight seam, seam width deviation of not more than 2mm.
8、電梯門套全部安裝完之后，將表面石材做一次清理工作，即可投入使用。
After 8, all installed the elevator door, a cleaning surface stone, can be put into use.
電梯門套施工注意事項
The elevator door construction matters needing attention
1、在安裝電梯門套時，想要將各層需要的石材挑選好。根據尺寸、顏色和花紋來搭配，然后搬運到各個樓層需要使用的地方。
1, installed in the elevator door, to each layer of stone selection. Match by size, color, and pattern, and then move to where each floor needs to be used.
2、在安裝時要注意石材的紋理，盡量保持色澤一致，紋理連貫。安裝完成之后，電梯門套的美觀性才會最佳。
2, in the installation should pay attention to stone texture, as far as possible to maintain color consistency, texture coherence. After the installation is complete, the appearance of the elevator door will be the best.
3、彈線的時候要仔細測量，不僅一個門套要做好垂直和平整性，每個門套之間也要注意這些問題。
When I was 3, playing the line must be measured carefully, not only a door to do vertical integration of peace, we should pay attention to these problems between each.
4、安裝角鋼的位置要測量精確，在中間增加一個加固點的點位。這樣做是為了讓門套石材更加穩定、牢固。
4. The position of the angle iron shall be measured accurately, and a point of reinforcement shall be added in the middle. This is done in order to make more stable and solid stone door.
以上的介紹，您了解了嗎?如果您有不明白的地方，歡迎您的致電，我們?nèi)鏋槟榻B，歡迎您的蒞臨參觀哦。
Have you got the above information? If you don't understand it, you are welcome to call us. We would like to introduce you to all of you.